In regards to the Lock N Roll Articulating Channel Tongue Trailer Coupler part # 336TS528, the distance from the bottom of the coupler base to the center of the mounting hole is 1-1/2". view full answer...
The hitch height of the Draw-Tite Front Mount Trailer Hitch Receiver part # 65069 will vary from vehicle to vehicle depending on factors such as tire size, aftermarket lift, suspension condition, load, etc. so we cannot give specifics but when we installed this same hitch on a 2017 Jeep Wrangler Unlimited we found the distance from the ground to the top inside edge of the receiver tube opening to be about 18-1/2". The bottom of the receiver tube opening would then be around 16-1/2".
Therefore,... view full answer...
The towing capacity of your motorhome should be listed in the owner's manual. Typically if you know your GVWR (gross vehicle weight rating) and your GCWR (gross combined weight rating) you can subtract your GVWR from your GCWR to find out how much you can tow. If you already have a trailer hitch installed on the motorhome it would have weight ratings listed on it as well but those can be higher than the weight rating of the vehicle it is installed on so it isn't a great way to determine... view full answer...
All weight distribution/sway control systems such as the Equal-i-zer 4-Point # EQ37060ET operate over a range of trailer tongue weight (TW). Ideally your actual TW will fall near the middle of the system's operating range. If the fully-loaded TWs of both trailers happen to fall within the systems operating range, in the case of this system 200- to 800-lbs, then the one system would work for both trailers. The different vehicles matter only in terms of their heights; two vehicles with different... view full answer...
I did some checking and the large bolt and the nuts that fit it on the Rampage Recovery Bumper with Swing Arm # RA88606 are 1-1/4"-7. That means 7 threads per inch so you would need 1-1/4 inch nuts with 7 threads per inch in the desired size to work with your application. view full answer...
There might be a chance you can tow your 2,800 lb pop up with a 2012 Jeep Wrangler Unlimited, but you will need to see if there is a separate capacity listed for weight distribution. Not all vehicles, but some have two capacities. One for weight carrying (without WD) and a capacity for with weight distribution.
If you find there is a weight distribution capacity for your vehicle and it is higher than 2,800 lbs you would be fine to tow your popup with a weight distribution hitch like the... view full answer...
I spoke with my contact at Lock N Roll about the Lock N Roll Articulating Hitch part # 336VS503505 and they were not quite sure what measurements you are looking for nor was I. That said, I went out to our warehouse for you and jotted down a few dimensions on the above in hopes these were what you were looking for. If it is not please try to further clarify this for me and I would be happy to remeasure this for you.
I have attached a photo below with the dimensions I think you are looking... view full answer...
I went to the warehouse to take a look at the Camco Gen-Turi RV Generator Exhaust System # CAM44461 and found that it extends to 120".
That measurement should tell you exactly how many of the 18" Camco Gen-Turi Extension # CAM44872 you'll need! view full answer...
Your ST255/R70-18 tire has an overall diameter of 32-inches so you can use a cover for 32-inch or 32-1/4-inch tires. Links to spare tire covers in both sizes, such as Rampage # RA783235 and Adco # 290-1782, are provided to let you see all spare tire cover options for your 2011 Jeep Wrangler Unlimited. view full answer...
I checked with Bestop and the Instatrunk Custom Cargo Area Storage Unit # B4270201 measures 11 inches high x 11 inches deep x 35 inches wide when installed in your 2010 Jeep Wrangler Unlimited. This will give you 2.7 cubic feet of storage space which is lockable; I've added a link to the install instructions for you to take a look at as well. view full answer...
For your application I recommend using the Draw-Tite Class III Trailer Hitch # DT78MR because when we installed it on a 2020 Jeep Wrangler Unlimited we found that from the center of the hitch pin hole to the rear edge of the bumper was 1". The Yakima FullSwing # Y02465 has a max distance of 6-3/4" from the center of the hitch pin hole to the furthest edge of the tire.
Since the Sahara has a different bumper than the normal Wrangler you'll likely need the RockyMounts Extender # RKY10008... view full answer...
The issue with the newer Jeep backup camera is the location of the camera as well as obstructed views when the rack is installed. There really isn't a great spare tire mounted option to avoid this issue, but either the Malone Hanger Spare T3 OS - Spare Tire Mount - 3 Bike Carrier - Anti-Sway Cages - Safety Reflectors # MPG2147 or the Hollywood Racks SR1 2-Bike Carrier - Spare Tire Mount # HRSR1 is the best option for view with bike rack loaded.
These bike racks do have width restrictions... view full answer...
We have dynamic weight capacities for our roof racks like the Rhino Rack you mentioned of 59inch Long Vortex Aero Crossbars # RRVA150B-2 and 8inch Tall Gutter Feet # RL210S2 which is rated for 165 lbs but we do not have a static number. Usually people request this number because they plan to use a roof rack mounted tent. You should note that most roof tents will say you can utilize the full weight capacity of the tent as long as the roof rack has a dynamic weight capacity of 165 lbs at least. view full answer...
Yes, we have confirmed the fit of the CIPA Universal Fit Towing Mirror # CM11980 on the mirrors of a 2013 Jeep Wrangler Unlimited just like yours so this would fit and work well for you.
I attached an install video for this mirror for you to check out as well. view full answer...
The spare tire on your 2016 Jeep Wrangler Unlimited poses a clearance challenge for transporting a wheelchair on a hitch-mounted carrier. The use of a hitch extension like # C45791 will get you an extra 8-inches of clearance at the spare tire, but the use of any adapter like this also costs you 50-percent of your hitch capacity. This is due to the extra leverage applied to the hitch from the load being further away from it.
The 2-inch hitches for your Wrangler Unlimited (shown on the linked... view full answer...
I went to our warehouse and took the measurement you asked for on the Swagman XTC4 4-Bike Rack, part # S64665.
I have attached a photo that has the measurement noted. The entire upright mast has teeth that allow you to move the hooks up and down. As the photo shows, the distance from the top of the mast base and also the top of the wheel hoop is 14 inches when the hook is in its lowest position.
This carrier has a 4 bike capacity with a weight capacity of 35 lbs per bike and is designed... view full answer...
It kind of depends on the accessory, but the largest channel nut that would be used is for the Eye Bolt Kit # RR43178. These channel nuts measure 2.36" long x 0.77" wide x 0.39" thick and then the diameter of the bolt itself that fits in the slit is 0.37". As long as your accessory doesn't exceed at least the width and the thickness you should be good to go. view full answer...
From the rear of the coupler portion on the Demco A-Frame Coupler # DM14793-81 to the center of the center bolt hole there is a distance of 4-1/2 inches. From the rear of the A-Frame mount to the center of the center hole there is a distance of 4-3/4 inches. From the top of the plate to the center of the mounting hole there is a distance of 1-3/4 inches.
I have attached a diagram to assist. view full answer...
I was able to fit a 7/8" socket on the hot and cold inlets for the Empire Faucets RV Bathroom Faucet # EM35PR so that's the size wrench you're going to need. view full answer...